SPEC 26125

HVTECK AL 1/C 90NLEPR CB PVC AIA PVC 5kV 100% CSA

Single Conductor, 90 Mils No Lead Ethylene Propylene Rubber (NL-EPR), 100% Insulation Level, Concentric Bond, Polyvinyl Chloride (PVC) Inner Jacket, Aluminum Interlocked Armour (AIA), Polyvinyl Chloride (PVC) Jacket

...

Construction:

  1. Conductor:Class B compact stranded 8000 Series aluminum per ASTM B800 and ASTM B836
  2. Conductor Shield:Semi-conducting cross-linked copolymer; A conductor separator is used for cable size larger than or equal to 500 Kcmil
  3. Insulation:90 Mils No Lead Ethylene Propylene Rubber (NL-EPR) 100% insulation level
  4. Insulation Shield:Strippable semi-conducting cross-linked copolymer
  5. Concentric Shield:Concentrically applied copper bond / shield wires. Complies with greater than the minimum requirement as per Table 44, CSA Standard C68.10 and Table 16A, Canadian Electrical Code Part 1
  6. Neutral Separator:Mylar tape
  7. Inner Jacket:PVC inner jacket
  8. Armour:Aluminum Interlocked Armour (AIA)
  9. Overall Jacket:Orange Polyvinyl Chloride (PVC) Jacket

Applications and Features:

Southwire's 5kV HVTECK is a CSA armoured cable for industrial and commercial medium voltage applications. Rated FT4, -40°C, Hazardous Locations (HL) and 105°C for use in harsh Canadian environments. For installation in cable trays, duct banks, direct burial, troughs, continuous rigid cable supports and concrete encaseable. When used in a 3 phase system, the combination of each bond conductor from each single conductor cable provide a 100% bonded system to ground.

Specifications:

  • ASTM B800 8000 Series Aluminum Alloy Wire
  • ASTM B836 Compact Rounded Stranded Aluminum Conductors
  • CSA C22.2 No. 174 Cables in Hazardous Locations
  • CSA C22.2 No. 2556 & No. 0.3 Wire and Cable Test Methods
  • CSA C68.10 Shielded Power Cables for Commercial and Industrial Applications - 5 to 46 KV
  • CSA C68.3 Shielded & Concentric Neutral Power Cable - 5 to 46 kV
  • CSA LTGG [-40°C] - as per C68.10 - for Cold Bend and Impact rating
  • CSA HL - for Hazardous Locations rating
  • CSA SUN RES - for Sunlight Resistant rating
  • ICEA S-93-639 (NEMA WC 74) 5-46 KV Shielded Power Cable
  • ICEA T-29-520 Flame Test (210,000 BTU/Hr)
  • IEEE 383 Flame Test (70,000 btu)
  • IEEE 1202 FT4 Flame Test (70,000) BTU/hr Vertical Tray Test (1/0 and Larger)
  • FT1 Flame Test (1,706 BTU/Hr nominal - Vertical Wire Flame Test)
  • AEIC CS-8 Specification for extruded dielectric shielded power cables rated for 5 through 46KV
  • Sample Print Legend:

    (CSA) SOUTHWIRE (NESC) #P# 1/C [#AWG or #kcmil] CPT AL 90 NLEPR AIA 5kV 100% INS LEVEL CB [No. x SIZE] AWG SUN RES 105°C FT4 HL (-40°C) LTGG RoHS YEAR [SEQUENTIAL METER MARKS]
    Table 1 – Weights and Measurements
    Stock NumberCond. SizeStrandDiameter Over ConductorDiameter Over InsulationInsul. ThicknessDiameter Over Insulation ShieldConcentric NeutralDia. Over Inner JacketDia. Over ArmourJacket Thickness1Approx. ODApprox. Weight
    AWG/KcmilNo.inchinchmilinchNo. x AWGinchinchmilinchlb/1000ft
    TBA270.2680.485900.56511x160.7971.007501.107556
    TBA1190.2990.516900.59611x160.8281.038501.138590
    TBA1/0190.3360.553900.63311x160.8651.075501.175632
    TBA2/0190.3760.593900.67317x160.9051.115501.215728
    TBA3/0190.4230.640900.72017x160.9521.272501.372866
    TBA4/0190.4750.692900.77217x161.0341.354501.454977
    TBA250370.5200.746900.82621x161.0881.408501.5081083
    TBA350370.6160.842900.92227x161.1841.504501.6041288
    TBA500370.7360.962901.04221x141.3301.650501.7501572
    TBA750610.9081.165901.26527x141.5531.873601.9932097
    TBA1000611.0601.317901.41727x141.7052.025602.1452441
    All dimensions are nominal and subject to normal manufacturing tolerances
    ◊ Cable marked with this symbol is a standard stock item
    1 Comply with ICEA S-93-639 Appendix C for jacket thickness determination
    Table 2 – Electrical and Engineering Data
    Cond. SizeMin Bending RadiusMax Pull TensionDC Resistance @ 25°CAC Resistance @ 90°CCapacitive Reactance @ 60HzInductive Reactance @ 60HzZero Sequence Impedance*Positive Sequence Impedance*Phase Short Circuit Current @ 60HzAllowable Ampacity in Vented Cable Tray 90°C‡Allowable Ampacity Directly Buried 90°C‡
    AWG/KcmilinchlbΩ/1000ftΩ/1000ftMΩ*1000ftΩ/1000ftΩ/1000ftΩ/1000ftkAmpAmpAmp
    27.73980.2660.3340.0320.0540.634+j0.1880.336+j0.0542.9169176
    18.05020.2110.2650.0290.0520.565+j0.1870.267+j0.0523.7194198
    1/08.26340.1680.2110.0270.0500.510+j0.1860.213+j0.0504.7222223
    2/08.57990.1330.1670.0250.0490.391+j0.1030.170+j0.0485.9255250
    3/09.610070.1050.1320.0220.0490.356+j0.1030.135+j0.0487.4290278
    4/010.212700.08360.1050.0200.0470.328+j0.1020.108+j0.0479.4329309
    25010.615000.07070.0890.0190.0460.278+j0.0770.093+j0.04511.1370347
    35011.221000.05050.0640.0170.0440.216+j0.0550.069+j0.04315.5446402
    50012.330000.03540.0450.0140.0420.170+j0.0430.050+j0.04022.1533451
    75014.045000.02360.0300.0130.0400.129+j0.0330.036+j0.03833.2631500
    100015.060000.01770.0230.0120.0380.122+j0.0330.029+j0.03644.3707539
    * Calculations are based on three cables triplexed / 5 mil 25 % over lapping copper tape shield / Conductor temperature of 90°C / Shield temperature of 45°C / Earth resistivity of 100 ohms-meter
    † Ampacities are based on Table D17M of the 2015 Canadian Electrical Code Part I (40°C Ambient Air Temperature, indoor installation)
    ‡ Ampacities are based on Table D17A of the 2015 Canadian Electrical Code Part I
    Table 3 – Weights and Measurements (Metric)
    Stock NumberCond. SizeStrandDiameter Over ConductorDiameter Over InsulationInsul. ThicknessDiameter Over Insulation ShieldConcentric NeutralDia. Over Inner JacketDia. Over ArmourJacket Thickness1Approx. ODApprox. Weight
    AWG/KcmilNo.mmmmmmmmNo. x AWGmmmmmmmmkg/km
    TBA276.8112.322.2914.3511x1620.2425.581.2728.12827
    TBA1197.5913.112.2915.1411x1621.0326.371.2728.91878
    TBA1/0198.5314.052.2916.0811x1621.9727.301.2729.85941
    TBA2/0199.5515.062.2917.0917x1622.9928.321.2730.861083
    TBA3/01910.7416.262.2918.2917x1624.1832.311.2734.851289
    TBA4/01912.0717.582.2919.6117x1626.2634.391.2736.931454
    TBA2503713.2118.952.2920.9821x1627.6435.761.2738.301612
    TBA3503715.6521.392.2923.4227x1630.0738.201.2740.741917
    TBA5003718.6924.432.2926.4721x1433.7841.911.2744.452339
    TBA7506123.0629.592.2932.1327x1439.4547.571.5250.623121
    TBA10006126.9233.452.2935.9927x1443.3151.431.5254.483633
    All dimensions are nominal and subject to normal manufacturing tolerances
    ◊ Cable marked with this symbol is a standard stock item
    1 Comply with ICEA S-93-639 Appendix C for jacket thickness determination
    Table 4 – Electrical and Engineering Data (Metric)
    Cond. SizeMin Bending RadiusMax Pull TensionDC Resistance @ 25°CAC Resistance @ 90°CCapacitive Reactance @ 60HzInductive Reactance @ 60HzZero Sequence Impedance*Positive Sequence Impedance*Phase Short Circuit Current @ 60HzAllowable Ampacity in Vented Cable Tray 90°C‡Allowable Ampacity Directly Buried 90°C‡
    AWG/KcmilmmnewtonΩ/kmΩ/kmMΩ*kmΩ/kmΩ/1000ftΩ/1000ftkAmpAmpAmp
    2195.5817710.87271.100.00980.17720.634+j0.1880.336+j0.0542.9169176
    1203.2022340.69230.870.00880.17060.565+j0.1870.267+j0.0523.7194198
    1/0208.2828210.55120.690.00820.16400.510+j0.1860.213+j0.0504.7222223
    2/0215.9035560.43640.550.00760.16080.391+j0.1030.170+j0.0485.9255250
    3/0243.8444810.34450.430.00670.16080.356+j0.1030.135+j0.0487.4290278
    4/0259.0856520.27430.340.00610.15420.328+j0.1020.108+j0.0479.4329309
    250269.2466750.23200.290.00580.15090.278+j0.0770.093+j0.04511.1370347
    350284.4893450.16570.210.00520.14440.216+j0.0550.069+j0.04315.5446402
    500312.42133500.11610.150.00430.13780.170+j0.0430.050+j0.04022.1533451
    750355.60200250.07740.100.00400.13120.129+j0.0330.036+j0.03833.2631500
    1000381.00267000.05810.080.00370.12470.122+j0.0330.029+j0.03644.3707539
    * Calculations are based on three cables triplexed / 5 mil 25 % over lapping copper tape shield / Conductor temperature of 90°C / Shield temperature of 45°C / Earth resistivity of 100 ohms-meter
    † Ampacities are based on Table D17M of the 2015 Canadian Electrical Code Part I (40°C Ambient Air Temperature, indoor installation)
    ‡ Ampacities are based on Table D17A of the 2015 Canadian Electrical Code Part I

    Revision: 3.0.00C