Name: HVTECK AL 1/C 260TRXLPE CB PVC AIA PVC 25kV 100% CSA
Brand: Southwire
Rating: 5 (1 reviews)

Products > Industrial Products > HVTECK > SPEC26435

SPEC 26435

HVTECK AL 1/C 260TRXLPE CB PVC AIA PVC 25kV 100% CSA

Single Conductor, 260 Mils Tree Retardant Cross Linked Polyethylene, 100% Insulation Level, Concentric Bond, Polyvinyl Chloride (PVC) Inner Jacket, Aluminum Interlocked Armour (AIA), Polyvinyl Chloride (PVC) Jacket

Download PDF

Construction:

Conductor:Class B compact stranded 8000 Series aluminum per ASTM B800 and ASTM B836
Conductor Shield:Semi-conducting cross-linked copolymer; A conductor separator is used for cable size larger than or equal to 500 Kcmil
Insulation:260 Mils Tree Retardant Cross Linked Polyethylene 100% insulation level
Insulation Shield:Strippable semi-conducting cross-linked copolymer
Concentric Shield:Concentrically applied copper bond / shield wires. Complies with greater than the minimum requirement as per Table 44, CSA Standard C68.10 and Table 16A, Canadian Electrical Code Part 1
Neutral Separator:Mylar tape
Inner Jacket:PVC inner jacket
Armour:Aluminum Interlocked Armour (AIA)
Overall Jacket:Black Polyvinyl Chloride (PVC) Jacket

Applications and Features:

Southwire's 25kV HVTECK is a CSA armoured cable for industrial and commercial medium voltage applications. Rated FT4, -40°C, Hazardous Locations (HL) and 105°C for use in harsh Canadian environments. For installation in cable trays, duct banks, direct burial, troughs, continuous rigid cable supports and concrete encaseable. When used in a 3 phase system, the combination of each bond conductor from each single conductor cable provide a 100% bonded system to ground.

Specifications:

ASTM B800 8000 Series Aluminum Alloy Wire

ASTM B836 Compact Rounded Stranded Aluminum Conductors

CSA C22.2 No. 174 Cables in Hazardous Locations

CSA C22.2 No. 2556 & No. 0.3 Wire and Cable Test Methods

CSA C68.10 Shielded Power Cables for Commercial and Industrial Applications - 5 to 46 KV

CSA C68.3 Shielded & Concentric Neutral Power Cable - 5 to 46 kV

CSA LTGG [-40°C] - as per C68.10 - for Cold Bend and Impact rating

CSA HL - for Hazardous Locations rating

CSA SUN RES - for Sunlight Resistant rating

ICEA S-93-639 (NEMA WC 74) 5-46 KV Shielded Power Cable

ICEA T-29-520 Flame Test (210,000 BTU/Hr)

IEEE 383 Flame Test (70,000 btu)

IEEE 1202 FT4 Flame Test (70,000) BTU/hr Vertical Tray Test (1/0 and Larger)

FT1 Flame Test (1,706 BTU/Hr nominal - Vertical Wire Flame Test)

AEIC CS-8 Specification for extruded dielectric shielded power cables rated for 5 through 46KV

Sample Print Legend:

(CSA) SOUTHWIRE (NESC) #P# 1/C [#AWG or #kcmil] CPT AL 260 TRXLPE AIA 25kV 100% INS LEVEL CB [No. x SIZE] AWG SUN RES 105°C FT4 HL (-40°C) LTGG RoHS YEAR [SEQUENTIAL METER MARKS]

Table 1 – Weights and Measurements

Stock Number	Cond. Size	Strand	Diameter Over Conductor	Diameter Over Insulation	Insul. Thickness	Diameter Over Insulation Shield	Concentric Neutral	Dia. Over Inner Jacket	Dia. Over Armour	Jacket Thickness¹	Approx. OD	Approx. Weight
	AWG/Kcmil	No.	inch	inch	mil	inch	No. x AWG	inch	inch	mil	inch	lb/1000ft
TBA	1	19	0.299	0.856	260	0.936	11x16	1.198	1.518	50	1.618	995
TBA	1/0	19	0.336	0.893	260	0.973	11x16	1.235	1.555	50	1.655	1047
TBA	2/0	19	0.376	0.933	260	1.013	17x16	1.275	1.595	50	1.695	1153
TBA	3/0	19	0.423	0.980	260	1.060	17x16	1.322	1.642	50	1.742	1226
TBA	4/0	19	0.475	1.032	260	1.112	17x16	1.374	1.694	50	1.794	1311
TBA	250	37	0.520	1.086	260	1.186	21x16	1.448	1.768	50	1.868	1455
TBA	350	37	0.616	1.182	260	1.282	27x16	1.544	1.864	60	1.984	1716
TBA	500	37	0.736	1.302	260	1.402	21x14	1.690	2.010	60	2.130	2026
TBA	750	61	0.908	1.505	260	1.605	27x14	1.953	2.283	60	2.403	2728
TBA	1000	61	1.060	1.657	260	1.787	27x14	2.135	2.465	60	2.585	3172

All dimensions are nominal and subject to normal manufacturing tolerances

◊ Cable marked with this symbol is a standard stock item

1 Comply with ICEA S-93-639 Appendix C for jacket thickness determination

Table 2 – Electrical and Engineering Data

Cond. Size	Min Bending Radius	Max Pull Tension	DC Resistance @ 25°C	AC Resistance @ 90°C	Capacitive Reactance @ 60Hz	Inductive Reactance @ 60Hz	Zero Sequence Impedance*	Positive Sequence Impedance*	Phase Short Circuit Current @ 60Hz	Allowable Ampacity in Vented Cable Tray 90°C‡	Allowable Ampacity Directly Buried 90°C‡
AWG/Kcmil	inch	lb	Ω/1000ft	Ω/1000ft	MΩ*1000ft	Ω/1000ft	Ω/1000ft	Ω/1000ft	kAmp	Amp	Amp
1	11.3	502	0.211	0.265	0.072	0.061	0.559+j0.199	0.267+j0.060	3.9	193	194
1/0	11.6	634	0.168	0.211	0.067	0.058	0.504+j0.198	0.213+j0.058	5.0	221	219
2/0	11.9	799	0.133	0.167	0.062	0.056	0.389+j0.115	0.170+j0.056	6.3	253	246
3/0	12.2	1007	0.105	0.132	0.057	0.054	0.354+j0.113	0.135+j0.054	7.9	288	275
4/0	12.6	1270	0.0836	0.105	0.053	0.052	0.326+j0.112	0.108+j0.052	9.9	327	305
250	13.1	1500	0.0707	0.089	0.050	0.051	0.277+j0.086	0.092+j0.051	11.8	367	343
350	13.9	2100	0.0505	0.064	0.044	0.049	0.216+j0.063	0.068+j0.048	16.4	443	399
500	14.9	3000	0.0354	0.045	0.039	0.046	0.170+j0.051	0.050+j0.045	23.5	529	451
750	16.8	4500	0.0236	0.030	0.034	0.044	0.129+j0.039	0.036+j0.042	35.3	633	505
1000	18.1	6000	0.0177	0.023	0.030	0.042	0.122+j0.038	0.028+j0.041	47.0	711	544

* Calculations are based on three cables triplexed / 5 mil 25 % over lapping copper tape shield / Conductor temperature of 90°C / Shield temperature of 45°C / Earth resistivity of 100 ohms-meter
† Ampacities are based on Table D17M of the 2015 Canadian Electrical Code Part I (40°C Ambient Air Temperature, indoor installation)
‡ Ampacities are based on Table D17A of the 2015 Canadian Electrical Code Part I

Table 3 – Weights and Measurements (Metric)

Stock Number	Cond. Size	Strand	Diameter Over Conductor	Diameter Over Insulation	Insul. Thickness	Diameter Over Insulation Shield	Concentric Neutral	Dia. Over Inner Jacket	Dia. Over Armour	Jacket Thickness¹	Approx. OD	Approx. Weight
	AWG/Kcmil	No.	mm	mm	mm	mm	No. x AWG	mm	mm	mm	mm	kg/km
TBA	1	19	7.59	21.74	6.60	23.77	11x16	30.43	38.56	1.27	41.10	1481
TBA	1/0	19	8.53	22.68	6.60	24.71	11x16	31.37	39.50	1.27	42.04	1558
TBA	2/0	19	9.55	23.70	6.60	25.73	17x16	32.39	40.51	1.27	43.05	1716
TBA	3/0	19	10.74	24.89	6.60	26.92	17x16	33.58	41.71	1.27	44.25	1824
TBA	4/0	19	12.07	26.21	6.60	28.24	17x16	34.90	43.03	1.27	45.57	1951
TBA	250	37	13.21	27.58	6.60	30.12	21x16	36.78	44.91	1.27	47.45	2165
TBA	350	37	15.65	30.02	6.60	32.56	27x16	39.22	47.35	1.52	50.39	2554
TBA	500	37	18.69	33.07	6.60	35.61	21x14	42.93	51.05	1.52	54.10	3015
TBA	750	61	23.06	38.23	6.60	40.77	27x14	49.61	57.99	1.52	61.04	4060
TBA	1000	61	26.92	42.09	6.60	45.39	27x14	54.23	62.61	1.52	65.66	4720

All dimensions are nominal and subject to normal manufacturing tolerances

◊ Cable marked with this symbol is a standard stock item

1 Comply with ICEA S-93-639 Appendix C for jacket thickness determination

Table 4 – Electrical and Engineering Data (Metric)

Cond. Size	Min Bending Radius	Max Pull Tension	DC Resistance @ 25°C	AC Resistance @ 90°C	Capacitive Reactance @ 60Hz	Inductive Reactance @ 60Hz	Zero Sequence Impedance*	Positive Sequence Impedance*	Phase Short Circuit Current @ 60Hz	Allowable Ampacity in Vented Cable Tray 90°C‡	Allowable Ampacity Directly Buried 90°C‡
AWG/Kcmil	mm	newton	Ω/km	Ω/km	MΩ*km	Ω/km	Ω/1000ft	Ω/1000ft	kAmp	Amp	Amp
1	287.02	2234	0.6923	0.87	0.0219	0.2001	0.559+j0.199	0.267+j0.060	3.9	193	194
1/0	294.64	2821	0.5512	0.69	0.0204	0.1903	0.504+j0.198	0.213+j0.058	5.0	221	219
2/0	302.26	3556	0.4364	0.55	0.0189	0.1837	0.389+j0.115	0.170+j0.056	6.3	253	246
3/0	309.88	4481	0.3445	0.43	0.0174	0.1772	0.354+j0.113	0.135+j0.054	7.9	288	275
4/0	320.04	5652	0.2743	0.34	0.0162	0.1706	0.326+j0.112	0.108+j0.052	9.9	327	305
250	332.74	6675	0.2320	0.29	0.0152	0.1673	0.277+j0.086	0.092+j0.051	11.8	367	343
350	353.06	9345	0.1657	0.21	0.0134	0.1608	0.216+j0.063	0.068+j0.048	16.4	443	399
500	378.46	13350	0.1161	0.15	0.0119	0.1509	0.170+j0.051	0.050+j0.045	23.5	529	451
750	426.72	20025	0.0774	0.10	0.0104	0.1444	0.129+j0.039	0.036+j0.042	35.3	633	505
1000	459.74	26700	0.0581	0.08	0.0091	0.1378	0.122+j0.038	0.028+j0.041	47.0	711	544

Revision: 3.0.00C